Yes, the 4L60E transmission does have a filter. It’s important to check with your owner’s manual or vehicle service center for specific recommendations for your particular car before beginning any work on it. If your car has a manual transmission, you may need to use up to 5 quarts (4.7 liters). Generally speaking, it is recommended to replace around 3-4 quarts (2.8-3.7 liters) when changing the filter in an automatic transmission. The exact amount of transmission fluid needed for a filter change will depend on the make and model of your vehicle, as well as the type of transmission you have. How Much Transmission Fluid is Needed for a Filter Change? It’s important to keep up with regular maintenance on your vehicle’s transmission in order to ensure its longevity and optimal performance over time. When replacing both the fluid and filter, make sure to check for any metal particles or other debris that could indicate internal damage within your transmission. The old filter should be discarded and replaced with an OEM-specified replacement part. To do this, you’ll need roughly 10 quarts of Dexron III Automatic Transmission Fluid (ATF). When changing the fluid in a 4L60E transmission, it is recommended to replace not only the filter but also the entire fluid. Make sure you buy a new gasket with the filter so that it seals properly against any leaks.Ĭhanging this filter is not complicated but it is best done by an experienced mechanic in order to ensure that all parts are replaced correctly and securely.Ĭredit: How Much Fluid Does a 4L60E Filter Change? It is important to use the correct filter for your particular make and model vehicle when changing the filter as incorrect filters can cause serious damage to the transmission. The 4L60E transmission filter should be changed every 30,000 miles or 24 months to keep your transmission functioning properly. Remember to keep a clean rag handy when removing any fluid from your transmission, as spilled oil can damage components of your engine. To access it, you will need to remove a few bolts from the pan and then use an appropriate wrench or socket to loosen the plug. The 4L60E transmission is found in many GM vehicles, and its drain plug can be located on the driver’s side of the transmission pan. It is important to note that this oil should not be interchanged with any other type, as doing so could cause major damage to your vehicle’s engine or transmission system. This type of transmission requires a higher viscosity oil than other types and should only be used in vehicles equipped with the 4L60E model. The 4L60E transmission fluid capacity is 8.5 quarts of Dexron III automatic transmission fluid. 4L60E Transmission Fluid Capacity And Type If you’re draining and refilling, you’ll need to replace all 8.4 quarts however if you’re just doing a partial drain and refill, make sure not to exceed 6 quarts or else there could be an overflow issue. When it comes to changing the filter and fluid on your 4L60E transmission, you should be aware that the total capacity is 8.4 quarts of Dexron III (or equivalent) automatic transmission fluid. 2004 Chevy Silverado 4L60e Transmission Fluid and Filter Change – Tahoe Suburban Sierra Yukon 1500 When it comes time for a 4L60E transmission fluid and filter change, it’s important to use quality parts from reliable suppliers in order to guarantee that your vehicle will remain safe and efficient on the road. This job is best done by an experienced professional who can ensure that all components are properly replaced for optimal performance. Most vehicles with 4L60E transmissions should have their transmission fluid and filter changed every 30,000 miles to keep the system running smoothly. Reinstall pan using new gaskets, fill with fresh automatic transmission fluid (ATF) until full, then reattach electrical connectors and lower your car back down to ground level.įinally test drive your car to ensure that everything is working correctly after making repairs. Remove filter as well as pan gasket before replacing with new ones. Unplug all electrical connections from the transmission and remove any bolts securing it to other parts.ĭrain out old fluid by removing drain plug located at bottom of transmission pan. Next, raise and support it on jack stands or ramps so you can access the underside of the vehicle. To change the fluid and filter in a 4L60E transmission, first warm up the vehicle to operating temperature.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |